Kis set ke marks badhenge normalised hoke??
Official answer keys now available
An 8 m long simply-supported elastic beam of rectangular cross-section (100 mm × 200 mm) is subjected to a uniformly distributed load of 10 kN/m over its entire span. The maximum principal stress (in MPa, up to two decimal places) at a point located at the extreme compression edge of a cross-section and at 2 m from the support is
ALL coaching walas( made easy , ies masters , ace academy) gave 90. even i answered 90 . can anyone please explain why officla answer is zero
At a small water treatment plant which has 4 filters, the rate of filtration and backwashing are 200 m3 /d/m2 and 1000 m3 /d/m2 , respectively. Backwashing is done for 15 min per day. The maturation, which occurs initially as the filter is put back into service after cleaning, takes 30 min. It is proposed to recover the water being wasted during backwashing and maturation. The percentage increase in the filtered water produced (up to two decimal places) would be
All coaching wala gave answer between 7.50 to 7.53 . I answered 7.52 but offical range is 7.75 to 7.95 . Please explain me if u know right solution.
in my opinion normalization will be in favour of set 1 and that will around 2 marks. Mine was set 2
Bhai priority intersection vale ka answer c diya hai set 1 mein
set 1 intersection SSD answer given is C option and RCC Short Column Ans given is by considering minimum eccentricity
78.34 set 1 according to official key what rank can be expected
Priority intersection... ka option C diya h wo to galat h yaar
SET 1, number of rapid sand filter beds req. = 21 if we take 24hrs time but time will be less bcz of backwashing nd some ppl took it 23.5 hrs and ans is diff. hence i think this Qn should be given Marks to All, what say?
I am getting 79 marks set 2. How much rank is expected?
Guys !! Ese pre 2018 All those who were getting good marks as per coaching keys and there name isn't in the list , inbox me . As I was getting 241(IES master) and 229(made easy) . So on approx 235 .. so I went to upsc today to inquire about my marks and there were around 20-30 students from various branches (majorly civil, mech) who were facing the same issue .. Few of Made easy staff people were also there .
Set 1 K traversing wale question Mai A or C dia h uska sirf A hona chahiye
Guys 70 marks obc set 2...should i expect any psu at all.. PLEASE HELP..
How many people are still getting above 80 in set 1 after official key?
In set 1 earth retaining wall question, difference of pressure before and after development of tension crack in clay backfill was asked - so I thought the value should be negative. But value given in answer key is positive. Does anyone else think it should be negative or do you think it should be positive?
An RCC short column (with lateral ties) of rectangular cross section of 250 mm × 300 mm
is reinforced with four numbers of 16 mm diameter longitudinal bars. The grades of steel
and concrete are Fe415 and M20, respectively. Neglect eccentricity effect. Considering
limit state of collapse in compression (IS 456 : 2000), the axial load carrying capacity of
the column (in kN, up to one decimal place), is.....
- Maine attempt hi nhi Kia
- Code ache se padho 0.4fck hota
- 0.446 aur 0.45fck laga ans 910+ aagya shit
0 voters
Yaar kisi ne DMRC me regular executive AM operations ke liye apply kiya kya based on GATE 2017 score? Payment failure issue ho raha h bar bar.
who will challenge this question coz as per iitg official answer key is not matching with any of the coaching institute?
An 8 m long simply-supported elastic beam of rectangular cross-section (100 mm × 200 mm) is subjected to a uniformly distributed load of 10 kN/m over its entire span. The maximum principal stress (in MPa, up to two decimal places) at a point located at the extreme compression edge of a cross-section and at 2 m from the support is