Tech paper morning shift wala easy tha ya day shift wala???
Electrical me total kitne application h
Cro deflection factor and insulation material Ka and kya tha ...29/7. Shift 2
Regarding total number of applicants in exam. (Note--i cannot confirm the authenticity of news)
What should be the cutoff of jvvn AE
Aen first shift 1. Laplace transform of unit step- 1/S 2. Induction motor running above synchronous speed-asynchronous generator 3. Parameters affect conductor resistance- frequency, spiralling and temperature 4. Capacitor in single phase induction motor- connected in series with starting winding 5. Medium line- 80-150m and 20kv to 100kv 6. Feedback in control system makes system- closed loop 7. Controller which reduce steady state error- integral control 8.meter suitable for dc measurement- PMMC 9. Own's bridge used- inductance measurement 10. Ke of energymeter numerical having metering constant of 3000- 2kw 11. Electrostatic instrument is used to measure- voltage 12. Maximum overshoot is a measure of- damping ratio 13. Pyrometer is used for measurement of- high temperature 14. Open circuit test is performed- on low voltage winding 15. For constant VA transformer efficiency depends on-site power factor 16. For defrencing and amplification used in control system- op amp 17. For basic multiplication gate used- AND gate 18.parallel resistance 900, 450and 200ohm current of 1amp- 125v 19. Unit of reluctance- AT/ab 20. Permittivity of free space-time 8.84*10^-12
bhai muje to aen ka non tech jen se jayada lengthy laga....cutoff kya rehegi any idea
132 kv 3 phase line 100km in length with radius 1.12cm ..each phase separated by 4.56m(diagram Was given in which three horizontly placed conductor separed by 4.56m were shown) ...fully transposed what is current per phase in line? How to solve this question???
Guys Share AEn technical questions as much you remember..
Bhai corona loss wala ka ansr kya yoga..3 phase or six phase...kisme jyada hoga
Aaj aen it ke exam mein jo phle question phuch gya tha woh logical to physical tha ya physical to logical.
AEN IT tech-60 Nontech-64 Branch EC
Syllabus kya aaya aen it m.. Plz share tech question
RVPN AE TECHNICAL (Q 51-59)
RVPN AE TECHNICAL (Q 26-50)
dfccil mei b tech allowed h ki ni?
RVPN AE TECHNICAL (Q 1-25)
i think questions are diffrent for diffrent company....
jvvnl AE electrical 2 aug 12-2
1. what is Poisson's ratio for metal (range)
2. laplace transfrom for unit step
3. what a machine move more then synchrnous speed then it will work as
4.A RC snubber circuit consists of a series combination of resistance Rs and capacitance Cs in parallel with the thyristor. Capacitor Cs in parallel with the device is sufficient to prevent unwanted dv/dt triggering of the SCR
5.advantage igbt over mosfet
6. ban ki aas rever
7. milk youjana in school
8. varable capactance diode
9. 3 phase to 6 phase than corna .. increase / constant/ decrease
10. if f= 50 to 60 then rating of transfomer= 120%
11. constant loss in transformer
12 effiencey depends on transformer
13. loss due to change in direction of magnetic field
14. open circuit test performe in which side
15. which divice use for amplifaction and perfomer operaion in control
16 which gate use for multiplaction in digital
17. what is top most color of white light pass through prism
These colors are often observed as light passes through a triangular prism. Upon passage throughthe prism, the white light is separated into its component colors - red, orange, yellow, green, blue and violet. The separation of visible light into its different colors is known as dispersion
18. what is value of induce emf . if L and flux given
19 free space permittivity 8.85×10−12 F/m.
20. In a lap winding, the number of parallel paths, a, is always equal to the number of poles, p, and also to the number of brushes.
21. shaded pole motor can move
22. why use final value theorem
23 feed back system use in
24 reluctance in ampere-turns per weber
Avunl jen ee gen cut?? What are your predictions??? Plzz tell....i m scoring 125 marks